mcrypt_decrypt

(PHP 4 >= 4.0.2, PHP 5)

mcrypt_decryptDecrypts crypttext with given parameters

Описание

string mcrypt_decrypt ( string $cipher , string $key , string $data , string $mode [, string $iv ] )

Decrypts the data and returns the unencrypted data.

Список параметров

cipher

Одна из констант MCRYPT_ciphername или название алгоритма в виде строки.

key

The key with which the data was encrypted. If it's smaller than the required keysize, it is padded with '\0'.

data

The data that will be decrypted with the given cipher and mode. If the size of the data is not n * blocksize, the data will be padded with '\0'.

mode

Одна из констант MCRYPT_MODE_modename, либо одна из следующих строк: "ecb", "cbc", "cfb", "ofb", "nofb" и "stream".

iv

Используется для инициализации в режимах CBC, CFB, OFB, а также в некоторых алгоритмах в режиме STREAM. Если IV не будет передан, в случае, если он необходим для используемого алгоритма, то функция сгенерирует предупреждение об ошибке и использует IV, все байты которого установлены в "\0".

Возвращаемые значения

Returns the decrypted data as a string.

Коментарии

It appears that mcrypt_decrypt pads the *RETURN STRING* with nulls ('\0') to fill out to n * blocksize.  For old C-programmers, like myself, it is easy to believe the string ends at the first null.  In PHP it does not:

    strlen("abc\0\0") returns 5 and *NOT* 3
    strcmp("abc", "abc\0\0") returns -2 and *NOT* 0

I learned this lesson painfully when I passed a string returned from mycrypt_decrypt into a NuSoap message, which happily passed the nulls along to the receiver, who couldn't figure out what I was talking about.

My solution was:
<?php
    $retval 
mcrypt_decrypt( ...etc ...);
   
$retval rtrim($retval"\0");     // trim ONLY the nulls at the END
?>
2005-07-13 21:26:39
http://php5.kiev.ua/manual/ru/function.mcrypt-decrypt.html
If you happen to be decrypting something encrypted in ColdFusion, you'll discover that its encrypt function apparently pads the plaintext with ASCII 4, the "end of transmission" character.

Building on eddiec's code, you can remove both nulls and EOTs with this:

<?php
    $retval 
mcrypt_decrypt( ...etc ...);
   
$retval rtrim($retval"\0\4");     // trim ONLY the nulls and EOTs at the END
?>
2008-10-02 13:15:29
http://php5.kiev.ua/manual/ru/function.mcrypt-decrypt.html
Автор:
To remove PKCS7 padding:

<?php
    $decrypted 
mdecrypt_generic($tdbase64_decode($enc_auth_token));
   
$dec_s strlen($decrypted);
   
$padding ord($decrypted[$dec_s-1]);
   
$decrypted substr($decrypted0, -$padding);
?>
2010-11-24 05:41:27
http://php5.kiev.ua/manual/ru/function.mcrypt-decrypt.html
Be careful, sometimes mcrypt_decrypt return additional white spaces to the uncrypted string; use trim() for deleting them. I was like 2 hours searching the error and it was that..
2011-04-17 11:24:13
http://php5.kiev.ua/manual/ru/function.mcrypt-decrypt.html
Автор:
Caution, MCRYPT_RIJNDAEL_256 is not equivalent to AES_256.

The way to make RIJNDAEL be decrypted from AES with openssl is to use MCRYPT_RIJNDAEL_128 and padd the string to encrypt before encrypting with the follwing function:

<?php
function pkcs5_pad ($text$blocksize) {
   
$pad $blocksize - (strlen($text) % $blocksize);
    return 
$text str_repeat(chr($pad), $pad);
}
?>

On the decryption, the choosing of AES_256 or AES_128, etc. is based on the keysize used in the crypting. In my case it was a 128bit key so I used AES_128.
2011-09-30 03:34:06
http://php5.kiev.ua/manual/ru/function.mcrypt-decrypt.html
To decrypt data coming from MySQL's AES_ENCRYPT function:

<?php

function mysql_aes_key($key)
{
   
$new_key str_repeat(chr(0), 16);
    for(
$i=0,$len=strlen($key);$i<$len;$i++)
    {
       
$new_key[$i%16] = $new_key[$i%16] ^ $key[$i];
    }
    return 
$new_key;
}

function 
aes_decrypt($encrypted,$key)
{
   
// if $encrypted is HEXed, then return it to binary
   
$encrypted pack('H*',$encrypted);

   
$key mysql_aes_key($key);
    return 
rtrim(mcrypt_decrypt(MCRYPT_RIJNDAEL_128,$key,$encrypted,MCRYPT_MODE_ECB,''),"\x00..\x1F");
}

?>

adapted from the article "Replicating MySQL AES Encryption Methods With PHP" (dated 2012-05-20) found somewhere online.
2013-05-21 19:17:58
http://php5.kiev.ua/manual/ru/function.mcrypt-decrypt.html
When i using this function i find some problem, with adding additional binary symbols in decode message. 
$sDecrypt – «2433091»
$sDecrypt strlen – 16 (before trim) 
$sDecrypt – «2433091»
$sDecrypt strlen – 7 (after trim)
At local PC this problem solved by using trim/trim, but if I send my encrypt message to sever, and try encrypt them, I see that my message is not 16 symbols, as it was in my local pc, it is 32 sybmols, after encode. And trim function not working. I look at symbols code and what I see 
    50
    52
    51
    51
    48
    57
    49
    0
    0
    0
    0
    0
    0
    0
    0
    0
    10
    158
    112
    183
    154
    27
    95
    85
    42
    35
    95
    54
    227
    41
    179
    77
After “tabulation symbols” I get some junk symbols, and  I solve this problems like this.
After mcrypt_decrypt I use this code 
$plaintext_dec = substr($plaintext_dec, 0, strpos($plaintext_dec, "\0"));
I think it is not best resolution for this problem, but I solve my problem :)
2016-02-29 13:44:50
http://php5.kiev.ua/manual/ru/function.mcrypt-decrypt.html
Look at function.openssl-decrypt for a replacement. 

Supports PHP 5 >= 5.3.0, PHP 7
2017-11-28 07:43:49
http://php5.kiev.ua/manual/ru/function.mcrypt-decrypt.html

    Поддержать сайт на родительском проекте КГБ