gzwrite
(PHP 4, PHP 5)
gzwrite — Бинарная запись в gz-файл
Описание
$zp
, string $string
[, int $length
] )
Записывает содержимое string в данный gz-файл.
Список параметров
-
zp -
Указатель на gz-файл, возвращённый, после его успешного открытия, функцией gzopen().
-
string -
Записываемая строка.
-
length -
Число записываемых байтов (до сжатия). Если указано, операция завершится после записи
lengthбайт или при достижении конца строкиstring.Замечание:
Обратите внимание, что если параметр
lengthзадан, конфигурационный параметр magic_quotes_runtime будет проигнорирован и удаление слэшей из записываемой строки не будет выполнено.
Возвращаемые значения
Возвращает число действительно записанных байт (без учёта сжатия) в поток gz-файла.
Примеры
Пример #1 Пример использования gzwrite()
<?php
$string = 'Какие-то данные для сжатия';
$gz = gzopen('somefile.gz','w9');
gzwrite($gz, $string);
gzclose($gz);
?>
Коментарии
This is a short example of use gzwrite function.
<?php
function gzcompressfile($source,$level=false){
$dest=$source.'.gz';
$mode='wb'.$level;
$error=false;
if($fp_out=gzopen($dest,$mode)){
if($fp_in=fopen($source,'rb')){
while(!feof($fp_in))
gzwrite($fp_out,fread($fp_in,1024*512));
fclose($fp_in);
}
else $error=true;
gzclose($fp_out);
}
else $error=true;
if($error) return false;
else return $dest;
}
?>
the function gzcompressfile() compress a file 'data.csv' to 'data.csv.gz'. the function return false if error, and the new file name if it's ok.
How about this instead:$s = file_get_contents('file.tar');
file_put_contents('file.tar.gz',gzencode($s,9));
katzlbtjunk's method is certainly shorter, but it is unusable for anything except small files. It would try to load the whole file into memory, then create an entire compressed copy, and only then write it to disk. The other method given below will not exhaust memory like that.This function add a line to a .gz compressed file
<?php
function AppendLineGz($file,$string) {
if (file_exists($file)) {
$lines = gzfile($file);
$lines[count($lines)] = "$string\r\n";
$input=implode($lines);
} else {$input="$string\r\n";}
$gz = gzopen($file,'w9');
gzwrite($gz, $input);
gzclose($gz);
}
?>
gz compression is often used with tar archives. Building tar archives is quite easy. Here is a code snipplet which can be used for building tar archives before compressing them to tar.gz.
<?php
//\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\
// Adds file header to the tar file, it is used before adding file content.
// f: file resource (provided by eg. fopen)
// phisfn: path to file
// archfn: path to file in archive, directory names must be followed by '/'
//\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\
function TarAddHeader($f,$phisfn,$archfn)
{
$info=stat($phisfn);
$ouid=sprintf("%6s ", decoct($info[4]));
$ogid=sprintf("%6s ", decoct($info[5]));
$omode=sprintf("%6s ", decoct(fileperms($phisfn)));
$omtime=sprintf("%11s", decoct(filemtime($phisfn)));
if (@is_dir($phisfn))
{
$type="5";
$osize=sprintf("%11s ", decoct(0));
}
else
{
$type='';
$osize=sprintf("%11s ", decoct(filesize($phisfn)));
clearstatcache();
}
$dmajor = '';
$dminor = '';
$gname = '';
$linkname = '';
$magic = '';
$prefix = '';
$uname = '';
$version = '';
$chunkbeforeCS=pack("a100a8a8a8a12A12",$archfn, $omode, $ouid, $ogid, $osize, $omtime);
$chunkafterCS=pack("a1a100a6a2a32a32a8a8a155a12", $type, $linkname, $magic, $version, $uname, $gname, $dmajor, $dminor ,$prefix,'');
$checksum = 0;
for ($i=0; $i<148; $i++) $checksum+=ord(substr($chunkbeforeCS,$i,1));
for ($i=148; $i<156; $i++) $checksum+=ord(' ');
for ($i=156, $j=0; $i<512; $i++, $j++) $checksum+=ord(substr($chunkafterCS,$j,1));
fwrite($f,$chunkbeforeCS,148);
$checksum=sprintf("%6s ",decoct($checksum));
$bdchecksum=pack("a8", $checksum);
fwrite($f,$bdchecksum,8);
fwrite($f,$chunkafterCS,356);
return true;
}
//\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/
// Writes file content to the tar file must be called after a TarAddHeader
// f:file resource provided by fopen
// phisfn: path to file
//\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/
function TarWriteContents($f,$phisfn)
{
if (@is_dir($phisfn))
{
return;
}
else
{
$size=filesize($phisfn);
$padding=$size % 512 ? 512-$size%512 : 0;
$f2=fopen($phisfn,"rb");
while (!feof($f2)) fwrite($f,fread($f2,1024*1024));
$pstr=sprintf("a%d",$padding);
fwrite($f,pack($pstr,''));
}
}
//\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/
// Adds 1024 byte footer at the end of the tar file
// f: file resource
//\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/
function TarAddFooter($f)
{
fwrite($f,pack('a1024',''));
}
?>
Read the description of gzwrite() very carefully. If the 'length' option is not specified, then the input data will have slashes stripped on systems where magic quotes are enabled. This is important information to know when compressing files.
<?php
$data = fread($fp, 5000);
gzwrite($fp2, $data, strlen($data));
?>
Is the correct way to avoid issues with magic quotes.